Author Archive | Matt

Tactical Handyman: S.T. Action Trainer Snap Cap Mod

Most modern firearms can be dry fired without risking parts breakage but that doesn’t mean it is good for them. That poor breech face and firing pin/striker gets beaten and battered every time you pull the trigger. A snap cap can go a long way toward cushioning the blow and it is best to use them during dry fire practice. Unfortunately, the clear plastic snap caps that have a spring dampened primer don’t feed well in semi-autos, the anodized aluminum ones get torn up by the extractor over time, and they are all expensive. The Tactical Handyman knows that there is a better way. The best snap caps are the ones you make yourself!

ST Action Pro Snap Cap Mod

Materials

This is going to be easy. We are starting with really good dummy rounds, the S.T. Action Trainer Dummy Rounds. These are great because they have real brass cases, are loaded with brightly colored fake bullets that completely fill the case, and they don’t cost much. When we are done with them, they will still be really good dummy rounds but they will also be snap caps. You will also need some RTV Silicone which you can find in the automotive section of your local hardware store, a toothpick, and a sharp knife.

Just to recap, you need:

  • Some S.T. Action Trainers
  • RTV Silicone
  • A toothpick
  • A sharp knife

Instructions

I said this was going be easy and I wasn’t kidding. You should be able to do these in large batches.

  1. Fill the void in the “primer pocket” of the S.T. Action Trainer with RTV Silicone. It may help to use the toothpick to pack it into the pocket. Make sure you fill it to overflowing – we will trim the excess later.
  2. Allow the RTV Silicone to cure as long as the silicone’s manufacturer states.
  3. Trim the “primer pocket” to flush with the sharp knife.
  4. Dry fire with the peace of mind of knowing that your firing pin/striker is being gently cushioned by your DIY snap caps.
ST Action Pro Snap Cap Mod Series

This photo shows the progression from empty “primer pocket”, to overfilled, to trimmed.

Wrap Up

When you are done, you will have the best of all worlds – a great dummy round that is also a great snap cap. These can be used to train malfunctions on the range or to make your dry fire trainer safer for you and easier on your gun. Every shooter needs a supply of good snap caps.

You can get your S.T. Action Trainer Dummy Rounds at TacStrike.

Pro-Tool Industries MAG-NA-FIRE Fire Starter

UPDATE 12/29/2015: Pro-Tool Industries has discontinued the MAG-NA-FIRE. You can view their new STRYKE-ALL Emergency Fire Pack at their website.

The Pro-Tool Industries MAG-NA-FIRE Fire Starter makes me weak in the knees. If you like survival gadgets, you better sit down.

MAG-NA-FIRE

The MAG-NA-FIRE Fire Starter machined from a block of magnesium so it can be scraped with the included scraper and used like you would any other magnesium fire starter. However, it also has a built in pencil sharpener style tinder scraper and a bullet puller so you can use gun powder to start a fire in a pinch. You can also remove the blade from the tinder scraper to be used as a small survival blade and if you plug the holes on the bullet puller it works as a survival whistle.

Are you kidding me? This thing is awesome! Check out the MAG-NA-FIRE at ProToolIndustries.com.

MSM Logo MultiWrap

msm-multiwrap-003

Mil-Spec Monkey recently introduced their MSM MultiWrap. I have have used similar products for years and found them to be very useful as a head covering in both cold and warm weather.

MultiWraps, and other similar products, are basically just a tube made from thin, stretchable polyester fabric. You’ll find tons of different ways to wear them depending on the conditions your find yourself in. They wick moisture fairly well and insulate just a bit when it is cold. The material is thin enough and flexible enough that they fold into a very small space.

I paid a lot more for several of these from a different brand. It is hard to imagine a more versatile piece of gear for $5.50. Check out the MSM Logo MultiWrap.

msm-multiwrap-002

SOG Knives Snarl Designed by Jason Brous

Jason Brous of Brous Blades recently burst on the tactical custom knife scene in a big way thanks in large part to his Silent Soldier neck knife design. The Silent Soldier is a compact, self-defense fixed blade design that offers excellent retention in spite of its small grip. The demand for the Silent Soldier is massive so you will be happy to know that there is now a production version of the Silent Soldier from SOG Knives called the Snarl.

SOG Snarl

The Snarl retains much of functional design of the Silent Soldier. It has 2 large finger loops that facilitate a variety of different holds and make the knife easy to retain. The wharncliffe blade profile is good for both self-defense and utilitarian tasks. The Snarl is ground from .25″ thick 9CR18MoV steel. It has a 2.3″ blade and a 4.3″ overall length. It comes with a molded plastic sheath.

The Snarl is available for pre-order at our affiliate KnifeCenter.

Powered by WordPress. Designed by Woo Themes