Shellback Tactical recently rolled out their all new, easier to use website. Check it out at ShellbackTactical.com and don’t forget to check out the sale items!
Author Archive | Matt
Behind the Scenes at Warrior Trail
Warrior Trail gave us a peak behind the curtain. This very cool series of photos shows their training plate production process. It’s kind of like the crayon factory episode of Mister Rogers’ Neighborhood but more tactical…
The production starts here where 100% recycled PVC, in powder form, goes into the hopper.
The PVC comes out of the extruder in a ribbon that is very hot. It is partially cooled with a water bath.
The PVC ribbon goes through a roller to compress it to the proper dimensions. It is still warm and flexible when it comes out of the roller.
It can take a while to reach a consistent quality from the roller. These rejected ribbons will be ground up and fed back into the hopper.
The ribbons are cut to length.
The corners are clipped and the bi-curve shape is applied.
The plates are cooled in a water bath before having their sharp edges removed and their iconic hole drilled.
MI Gen-2 SS Hand Guards for DPMS Pattern .308 Uppers
It often seems like AR-10 shooters are left out in the cold when it comes to free float hand guards. There are new options everyday for the AR-15 but AR-10 options are few and far between. Well, I have good news. The excellent Midwest Industries Gen-2 SS Hand Guards will be available soon for DPMS pattern high and low receivers.
The 12″ high and low models (12.4 ounces) including the barrel nut) are available now by phone. They will be on the MI website soon. The 15″ models (14.3 ounces) will be available in two weeks.
Check out Midwest Industries.
MFT BATTLELINK Minimalist Paracord Mod
Some people have expressed concern that the hooked shape of the newly released BATTLELINK Minimalist Stock from Mission First Tactical (MFT) could pose a snag hazard. Some enterprising users have found a way to prevent any potential snags and keep some emergency paracord on hand. MFT will be offering these paracord straps as an accessory or you can make your own.
Check out the BATTLELINK Minimalist Stock at Mission First Tactical. I have one of these stocks inbound for review so stay tuned.
Review: BAD-EPS (Battle Arms Development – Ehanced Pin Set)
You probably never think of your AR-15’s pivot pin and take-down pin until you are fishing around in your gear looking for some kind of improvised tool to push a stubborn one out so you can access the interior of the receiver for some reason. You may not think much about your pivot and take-down pins but Battle Arms Development does and they set out to make them better.
Overview
The BAD-EPS is sold in a set. Each set consists of an EPP (Enhanced Pivot Pin) and ETP (Enhanced Take-down Pin). Each set also comes with two KNS hardened stainless steel detents, two 17-7 nickel plated stainless steel pin springs, and a high-strength neodymium magnet (more on that magnet later).
They are machined from 12L14 steel bar stock, case hardened, and finished in milspec black maganese phosphate.
Observations from Use
These little buggers are packed with features. The most revolutionary of the features will change the way you assemble lower receivers forever. The EPP (pivot pin) has a small dimple at the end that, when used with the included magnet, holds the detent in place allowing you to simply depress the pivot pin spring and press it into place the receiver with the detent itself. A job that used to be a severe pain in the rear can now be accomplished in a few seconds with one hand. It is like magic. I never want to screw around with a standard pivot pin again.
The rest of the features deal with making the pins easier to use after they are installed. Battle Arms Development added features to the pins to make them easier to press out of the receiver and easier to grasp.
The pins are about .030″ longer than a standard pin. This makes them considerably easier to press out of the receiver and easier to grasp when you have pushed them through. That little .030″ extra length makes a noticeable difference, especially when you push them in as far as the receiver will allow with your finger or a blunt tool because now the heads are sticking out the other side of the receiver .030″ further than they would be with standard pins.
The pins also feature shallow divots on the tips. These divots serve to help “trap” whatever tool you might be using to press the pins out so the tool is less likely to slip off the pin and mar the receiver. I don’t necessarily care about marring the receiver but I like that the divots allow me to use more force without slipping off the pin. Basically, they make using a tool to push the pins a lot easier.
The pin’s heads are both works of functional art. Battle Arms Development has managed to add grip without adding bulk. The heads on these pins are the same size as standard pins. That is a good thing because bulky pins can interfere with the use of an ambidextrous selector. The EPP features small dimples and an undercut shape that improve grip. The ETP has fine checkering around the circumference of the head and an broad, undercut that is strategically located to let you hook your finger tip under the pin head for removal.
Wrap Up
Standard pivot and take-down pins work. The Battle Arms Development Enhanced Pin Set works better. I am not sure I can honestly say that these are “must have gear” but I can honestly say that I wouldn’t want to be without them – especially if I was building a new lower and wrestling with the pivot pin installation.
Check out the BAD-EPS at Battle Arms Development.