Review: Danger Close Consulting Low Pro Scout Mount

Here is the bottom line up front…The Danger Close Consulting (DCC) Low Pro Scout Mount is the mount that should come with the Surefire M600 Scout Light from the start! I have had this for a couple of weeks now and it is everything that I hoped it would be and does everything I hoped it would do.

The DCC Low Profile Scout Mount works great on the Daniel Defense 9.5FSP Lite Rail.

Problem Solver

I think the one of the best compliments you can pay to a piece of gear is to say that it solves a problem. This mount solves multiple problems. The M600 Scout Light is a great weapon light in its stock form but it has some shortcomings, especially for those who will be using it without the remote pressure pad switch (I despise them). The stock mount places the light too low in relation to the shooter’s support hand grip. The light falls in a place that is awkward to reach with the support hand thumb. The stock mount also places the light high above the rail and has a large thumb screw that can be a snag magnet.

The DCC Low Pro Mount allows the user to place the light at around 11 o’clock on the rail and it tucks the light in very close to the rail. This is a much more natural position to hit with the thumb of the support hand and there is no more thumb screw to snag anything and everything.

Here you can see just how low profile the mount really is.

Attention to Detail

Attention to detail is often what separates good gear from great gear and the DCC Low Pro Scout Mount is great gear. The mount is very nicely machined with no visible machining marks. The hard anodized finish is smooth and evenly applied. There is a large hole that has been machined away to save weight. It would have been easier and cheaper to just machine a round hole, but DCC chose to mill a more complex shape that would save more weight. The set screw that provides tension against the rail even has a small rubber pad to prevent the steel screw from gouging your aluminum rails. That is attention to detail.

Note the lightening cut.

Locked Down

This mount is solid. The light is held to the mount with 2 screws (provided). I used a bit of Loc-Tite on both screws. The mount itself must be slid onto the rail from the end. The set screw should then be positioned in a rail slot. Once the set screw is in position, you simply tighten the set screw. This keeps the mount from moving forward and back by dropping into a slot and by pulling the mount up against the under side of the rail. It is rock solid.

Here you can see the two mounting screws and the green rubber pad on the set screw.

In Use

The difference when you are actually using the light must be felt to be believed. Those who are familiar with trying to use an M600 Scout Light with the factory mount will know immediately what an improvement this mount has the potential to be. I shoot with a vertical grip but I don’t wrap my hand around it. I use a thumb forward grip on it much like I would with my support hand when shooting a handgun. The original Surefire mount didn’t work very well with this grip. It was simply too low since it could only be mounted at 9 o’clock on the rail. I would have to contort my hand and shift my grip to get my thumb down to the tail cap which basically meant that I left the light unused. Now, with the DCC, the tail cap falls much more naturally under my support hand thumb at around 11 o’clock on the rail. I no longer have to shift or contort my grip and the light is much more usable.

Verdict: Buy One!

Jon at DCC is a genuinely nice guy and he is active in the Army Special Forces so he knows a bit about what makes gear work. If that isn’t enough reason to buy one, then knowing that this is the only mount of its kind should be. If you running the M600 Scout Weapon Light with the “clickie” tail cap then you need this mount. Buy one.

Look for an upcoming interview with Jon at Danger Close Consulting on Jerking the Trigger.

Add to FacebookAdd to DiggAdd to Del.icio.usAdd to StumbleuponAdd to RedditAdd to BlinklistAdd to TwitterAdd to TechnoratiAdd to Yahoo BuzzAdd to Newsvine

, , , ,

Trackbacks/Pingbacks

  1. The Regular Guy Sessions: Jon at Danger Close Consulting « Jerking the Trigger - June 16, 2010

    […] we will be talking with Jon at Danger Close Consulting (DCC). Jon is the man responsible for the recently reviewed Low Pro Scout Mount as well as other excellent light mounts (and some pretty hilarious t-shirts). I first found Danger […]

  2. LaRue Tactical LT752 Offset QD Mount for SureFire Scout WeaponLights « Jerking the Trigger - November 13, 2010

    […] have never had so many great choices in offset mounts. I have written previously about the Danger Close Consulting Scout Mount and the Gear Sector Scout Mount. Now LaRue has introduced the LT752 Offset QD Mount for Surefire […]

Powered by WordPress. Designed by Woo Themes